Justification for the introduction of additive manufacturing on machine-building enterprise
DOI:
https://doi.org/10.28983/asj.y2022i9pp104-107Keywords:
technology, additive manufacturing, 3D printing, computer-aided design, FDM, SLSAbstract
Modern mechanical engineering is increasingly beginning to be a symbiosis of related technologies and means of manufacturing finished products, having gone through all the stages from a sketch to a fully functional prototype. One of the key breakthroughs in reducing the cost of manufacturing products is the introduction of additive manufacturing (AM) at machine-building enterprises. The paper considers the most popular and relevant types of AP technologies, gives a methodology for determining the efficiency factor for introducing this type of production to a machine-building enterprise. The work also demonstrates the creation of an AP site on the basis of the Federal Scientific Agroengineering Center "VIM".
Downloads
References
Возможности применения 3D- технологий в ремонтном производстве / Ю.В. Башкирцев [и др.]. М.: ФГБОУ РИАМА, 2020. 44 с.
Голубев И.Г., Федоренко В.Ф. Перспективы применения аддитивных технологий при производстве и техническом сервисе сельскохозяйственной техники. 2-е изд. М., 2020. 137 с.
Дорохов А.С., Свиридов А.С. Применение аддитивных технологий при техническом сервисе садовой техники // Агроинженерия. 2020. № 6 (100). С. 39-44.
Дорохов А.С. Входной контроль качества машиностроительной продукции, поставляемой сельскому хозяйству. М., 2010. 211 с.
Дорохов А.С., Катаев Ю.В., Краснящих К.А., Вялых Г.М. Компьютерное проектирование в системе AUTOCAD. М., 2016. 80 с.
Ерохин М.Н., Казанцев С.П., Дорохов А.С. Компьютерные технологии проектирования в учебном процессе агроинженерных вузов // Вестник Федерального государственного образовательного учреждения высшего профессионального образования "Московский государственный агроинженерный университет имени В.П. Горячкина". 2010. № 4 (43). С. 82-85.
Панков Д.Э., Соломонов И.А., Терин А.М., Тутушкин А.К. Лазерная стереолитография (SLA): технология 3D-печати // Молодой ученый. 2020. № 48 (338). С. 48-49.
Sviridov A., Lopatina Yu., Kurganova I. 3D-printed polyether ether ketone samples mechanical properties estimation // IOP Conference Series: Materials Science and Engineering. 2019. С. 012021.
Свиридов А.С., Тужилин С.П., Лопатина Ю.А. Использование цифровой 3D-фермы в ремонтном производстве сельскохозяйственной техники // Технический сервис машин. 2019. № 1 (134). С. 93-99.
Славкина В.Э., Мирзаев М.А., Лопатина Ю.А.Применение технологии 3D-печати для оптимизации ремонта зубчатых передач // Технический сервис машин. 2020. № 1 (138). С. 58-64.
Downloads
Published
Issue
Section
License
Copyright (c) 2022 The Agrarian Scientific Journal
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.